Zum Inhalt springen

25 GHz TriMode Probing: What Tektronix’s P7725 Means for DDR6 and High-Speed I/O Debug

In high-speed debugging, the probe is often the weakest link in the measurement chain. A fast oscilloscope cannot show an edge that the probe has already slowed down. Tektronix has extended its TriMode probe family to 25 GHz with the new P7725, aimed at DDR6, LPDDR6 and high-speed I/O work. Here is what was announced, why probe bandwidth and loading decide what you see, how the P7725 compares with earlier TriMode models, and what to check when buying high-bandwidth scopes and probes new or pre-owned.

What Tektronix announced

On October 27, 2026, Tektronix announced the TriMode P7725 probe:

  • 25 GHz bandwidth, raising the top of the TriMode family from 20 GHz.
  • Designed for the Tektronix 7 Series DPO oscilloscope.
  • TriMode architecture: differential, single-ended and common-mode measurements from one probe connection.
  • Target applications include DDR5, DDR6, LPDDR5, LPDDR5X, LPDDR6, HDMI, DisplayPort and MIPI.
  • Two new accessories: the P77STFLXA24 active solder-in tip, which extends direct-access measurements to 24 GHz, and the P77C292MM SMA adapter for coax-connected signals up to 25 GHz.
  • Available now through Tektronix and its distribution partners.

The TriMode datasheet adds that the P7725 needs 7 Series DPO firmware 2.28.18 or later, and lists a typical rise time (10–90%) below 20 ps with the SMA adapter.

Why probe bandwidth and loading decide what you see

Rise time, bandwidth and the rule of thumb

For a system with a roughly Gaussian response, rise time (10–90%) is about 0.35 divided by bandwidth. The scope and probe together form one system, and their rise times combine, approximately, as the square root of the sum of squares. A common rule of thumb is to make the measurement system several times faster than the edge you want to measure, often quoted as three to five times. Treat that as a starting point, not a specification: check the actual rise time of your signal and the published rise time of the probe and scope.

Loading: the other half of the story

Every probe draws a little energy from the circuit. At tens of gigahertz, even a fraction of a picofarad of input capacitance can change the edge you are trying to measure. Tektronix lists P7700-series loading of 100 kΩ (DC) and 0.4 pF (AC). Low loading matters as much as bandwidth when you probe memory buses at the via or the pad.

Differential, single-ended and common-mode in one setup

High-speed serial and memory signals are usually differential, but common-mode noise and the single-ended legs often hide the root cause of a problem. Switching modes without re-soldering a tip saves time, and it avoids the risk of damaging a fragile board by attaching and removing tips repeatedly.

P7725 vs. earlier TriMode probes

ModellBandwidth (Tektronix datasheet)Scope familyTypische Anwendung
P77088 GHzDPO70000C/D/DX/SX series, 7 Series DPOEntry point of the family
P771313 GHzSame as aboveMid-range bandwidth
P771616 GHzSame as aboveFaster edges, more margin
P772020 GHzSame as abovePrevious top of the family
P772525 GHz (16 GHz in common-mode)7 Series DPO, firmware 2.28.18 or laterDDR6, LPDDR6, HDMI, DisplayPort, MIPI

The datasheet lists P7700-series compatibility with the DPO70000C, DSA70000C, MSO70000C, DPO70000D, DSA70000D, DPO70000DX, MSO70000DX and DPO70000SX series and the 7 Series DPO, with TekScope firmware 10.6 or higher for the Windows-based models. The P7725 itself is specified for the 7 Series DPO. Application targets for the P7725 come from the Tektronix announcement; the other rows are TXRX’s general guidance.

What it means for buyers of new and pre-owned scopes and probes

Match the probe to the scope

A probe is only useful on a scope that recognizes it. Check three things before buying either one: the probe interface the scope accepts, the firmware version, and whether the scope’s bandwidth is at least as high as the probe’s. A 25 GHz probe on a lower-bandwidth scope will not show more than the scope can.

High-bandwidth scopes available from TXRX

TXRX does not currently list Tektronix TriMode probes. For high-speed signal work, related instruments in our range include the Keysight DSOZ594A und Keysight UXR0592A real-time oscilloscopes, the Keysight MXR608A, and the Tektronix DSA8300 digital sampling oscilloscope. Note the difference: a real-time scope captures single events, while a sampling scope like the DSA8300 builds up repetitive waveforms and is used for eye diagrams and TDR rather than one-shot debugging. Each brand uses its own probe interface, so probes are generally not interchangeable between brands. For power integrity, see the Keysight N7020A power rail probe.

Keysight DSOZ594A Infiniium Z-Series real-time oscilloscope, front panel with eye diagram display

Keysight DSOZ594A: representative image from the product page.

Used high-bandwidth probe checklist

  • Inspect the tips and accessory connector first; they are the most fragile parts.
  • Ask whether the probe has been calibrated or performance-verified, and when.
  • Check that solder-in tips, adapters and cases are included, since replacement tips are consumables.
  • Confirm compatibility with your exact scope model and firmware in the manufacturer’s documentation.
  • Handle with ESD precautions; active probe inputs are easily damaged.

Häufig gestellte Fragen

How much probe bandwidth do I need for DDR5 or DDR6?

Start from the fastest rise time on your signal, not the data rate. Use the 0.35/bandwidth approximation to estimate the bandwidth that rise time requires, then choose a probe and scope comfortably faster. Check the memory standard’s own measurement guidance as well.

What does TriMode mean?

It is Tektronix’s name for probes that make differential, single-ended and common-mode measurements from one connection, switched from the scope without moving the probe.

Can I use a P7725 with older Tektronix oscilloscopes?

Tektronix specifies the P7725 for the 7 Series DPO with firmware 2.28.18 or later. For other models, check Tektronix’s current compatibility information before buying.

What should I check when buying a used high-bandwidth probe?

Tip and connector condition, calibration or verification records, included accessories, and confirmed compatibility with your scope and firmware.

Bottom line

The P7725 shows how much of high-speed debugging depends on the probe, not just the scope. If you are building or extending a signal integrity bench, match bandwidth, loading and interface across probe and scope, and budget for tips. Browse our oscilloscopes, oscilloscope probes and current probes und network analyzers for fixture de-embedding, or see our instrument repair services for scopes and probes that need attention.


Quelle: Tektronix, “Tektronix expands TriMode portfolio with new 25 GHz probe”, October 27, 2026. Original announcement: https://www.tek.com/en/news/p7725probe. Specifications: Tektronix TriMode Probe Family datasheet.

This article is an independent summary and commentary by TXRX. Quoted passages are attributed to Tektronix. All trademarks belong to their respective owners. TXRX is an independent supplier of new and pre-owned test equipment and is not affiliated with, endorsed by, or an authorized distributor of Tektronix.


Über TXRX — TXRX supplies new and pre-owned RF, microwave, optical and high-speed test instruments to labs and manufacturers worldwide. TXRX pre-owned equipment comes with a 6-month warranty; new equipment carries the manufacturer’s standard warranty. Learn more about TXRX · Contact us for a quote

Drafted with AI assistance and reviewed by the TXRX team.

Diesen Artikel teilen